[Prev][Next][Index][Thread]
Re: problems with ethernet initialization
> I've been trying to get the netboot kernel up and running. I don't get
> far, however, since the kernel is unable to find any ethernet devices.
> The machine has a 3Com 3C900 PCI Ethernet card, and Linux uses the 3c59x
> (vortex) driver.
The oskit use drivers from linux-2.0.29, and those cards are not supported
in that version. Hopefully we will update the drivers from a newer linux
version one of these days.
I have had some success with plopping in drivers from linux-2.0.35 with
slight modification. I attach below a replacement
linux/src/drivers/net/3c59x.c based on linux-2.0.35, which should support
the newer 3c90x cards. That might work for you, but I make no guarantees.
Enjoy,
Roland
/* EtherLinkXL.c: A 3Com EtherLink PCI III/XL ethernet driver for linux. */
/*
Written 1996-1998 by Donald Becker.
This software may be used and distributed according to the terms
of the GNU Public License, incorporated herein by reference.
This driver is for the 3Com "Vortex" and "Boomerang" series ethercards.
Members of the series include Fast EtherLink 3c590/3c592/3c595/3c597
and the EtherLink XL 3c900 and 3c905 cards.
The author may be reached as becker@CESDIS.gsfc.nasa.gov, or C/O
Center of Excellence in Space Data and Information Sciences
Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771
*/
static char *version =
"3c59x.c:v0.99E 5/12/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html\n";
/* "Knobs" that adjust features and parameters. */
/* Set the copy breakpoint for the copy-only-tiny-frames scheme.
Setting to > 1512 effectively disables this feature. */
static const int rx_copybreak = 200;
/* Allow setting MTU to a larger size, bypassing the normal ethernet setup. */
static const int mtu = 1500;
/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
static int max_interrupt_work = 20;
/* Put out somewhat more debugging messages. (0: no msg, 1 minimal .. 6). */
#ifdef VORTEX_DEBUG
static int vortex_debug = VORTEX_DEBUG;
#else
static int vortex_debug = 1;
#endif
/* Some values here only for performance evaluation and path-coverage
debugging. */
static int rx_nocopy = 0, rx_copy = 0, queued_packet = 0, rx_csumhits;
/* Enable the automatic media selection code -- usually set. */
#define AUTOMEDIA 1
/* Allow the use of fragment bus master transfers instead of only
programmed-I/O for Vortex cards. Full-bus-master transfers are always
enabled by default on Boomerang cards. If VORTEX_BUS_MASTER is defined,
the feature may be turned on using 'options'. */
#if YOU_ARE_BRAVER_THAN_ME
#define VORTEX_BUS_MASTER
#endif
/* A few values that may be tweaked. */
/* Time in jiffies before concluding the transmitter is hung. */
#define TX_TIMEOUT ((400*HZ)/1000)
/* Keep the ring sizes a power of two for efficiency. */
#define TX_RING_SIZE 16
#define RX_RING_SIZE 32
#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
#include <linux/config.h>
#ifdef MODULE
#ifdef MODVERSIONS
#include <linux/modversions.h>
#endif
#include <linux/module.h>
#include <linux/version.h>
#else
#define MOD_INC_USE_COUNT
#define MOD_DEC_USE_COUNT
#endif
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/errno.h>
#include <linux/in.h>
#include <linux/ioport.h>
#include <linux/malloc.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/bios32.h>
#include <linux/timer.h>
#include <asm/irq.h> /* For NR_IRQS only. */
#include <asm/bitops.h>
#include <asm/io.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
/* Kernel compatibility defines, common to David Hind's PCMCIA package.
This is only in the support-all-kernels source code. */
#ifndef LINUX_VERSION_CODE
#include <linux/version.h> /* Redundant above, here for easy clean-up. */
#endif
#if LINUX_VERSION_CODE < 0x10300
#define RUN_AT(x) (x) /* What to put in timer->expires. */
#define DEV_ALLOC_SKB(len) alloc_skb(len, GFP_ATOMIC)
#if defined(__alpha)
#error "The Alpha architecture is only support with kernel version 2.0."
#endif
#define virt_to_bus(addr) ((unsigned long)addr)
#define bus_to_virt(addr) ((void*)addr)
#define NR_IRQS 16
#else /* 1.3.0 and later */
#define RUN_AT(x) (jiffies + (x))
#define DEV_ALLOC_SKB(len) dev_alloc_skb(len)
#endif
#if LINUX_VERSION_CODE < 0x20159
#define DEV_FREE_SKB(skb) dev_kfree_skb (skb, FREE_WRITE);
#else /* Grrr, unneeded incompatible change. */
#define DEV_FREE_SKB(skb) dev_kfree_skb(skb);
#endif
#ifdef SA_SHIRQ
#define FREE_IRQ(irqnum, dev) free_irq(irqnum, dev)
#define REQUEST_IRQ(i,h,f,n, instance) request_irq(i,h,f,n, instance)
#define IRQ(irq, dev_id, pt_regs) (irq, dev_id, pt_regs)
#else
#define FREE_IRQ(irqnum, dev) free_irq(irqnum)
#define REQUEST_IRQ(i,h,f,n, instance) request_irq(i,h,f,n)
#define IRQ(irq, dev_id, pt_regs) (irq, pt_regs)
#endif
#if (LINUX_VERSION_CODE >= 0x10344)
#define NEW_MULTICAST
#include <linux/delay.h>
#else
#define udelay(microsec) do { int _i = 4*microsec; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
#endif
#if LINUX_VERSION_CODE < 0x20138
#define test_and_set_bit(val, addr) set_bit(val, addr)
#endif
#if defined(MODULE) && (LINUX_VERSION_CODE >= 0x20115)
MODULE_AUTHOR("Donald Becker <becker@cesdis.gsfc.nasa.gov>");
MODULE_DESCRIPTION("3Com 3c590/3c900 series Vortex/Boomerang driver");
MODULE_PARM(debug, "i");
MODULE_PARM(options, "1-" __MODULE_STRING(8) "i");
MODULE_PARM(full_duplex, "1-" __MODULE_STRING(8) "i");
MODULE_PARM(rx_copybreak, "i");
MODULE_PARM(max_interrupt_work, "i");
MODULE_PARM(compaq_ioaddr, "i");
MODULE_PARM(compaq_irq, "i");
MODULE_PARM(compaq_prod_id, "i");
#endif
/* Operational parameter that usually are not changed. */
/* The Vortex size is twice that of the original EtherLinkIII series: the
runtime register window, window 1, is now always mapped in.
The Boomerang size is twice as large as the Vortex -- it has additional
bus master control registers. */
#define VORTEX_TOTAL_SIZE 0x20
#define BOOMERANG_TOTAL_SIZE 0x40
#ifdef HAVE_DEVLIST
struct netdev_entry tc59x_drv =
{"Vortex", vortex_pci_probe, VORTEX_TOTAL_SIZE, NULL};
#endif
/* Set iff a MII transceiver on any interface requires mdio preamble.
This only set with the original DP83840 on older 3c905 boards, so the extra
code size of a per-interface flag is not worthwhile. */
static char mii_preamble_required = 0;
/* Caution! These entries must be consistent. */
static const int product_ids[] = {
0x5900, 0x5920, 0x5970, 0x5950, 0x5951, 0x5952, 0x9000, 0x9001,
0x9050, 0x9051, 0x9055, 0x5057, 0 };
static const char *product_names[] = {
"3c590 Vortex 10Mbps",
"3c592 EISA 10mbps Demon/Vortex",
"3c597 EISA Fast Demon/Vortex",
"3c595 Vortex 100baseTX",
"3c595 Vortex 100baseT4",
"3c595 Vortex 100base-MII",
"3c900 Boomerang 10baseT",
"3c900 Boomerang 10Mbps/Combo",
"3c905 Boomerang 100baseTx",
"3c905 Boomerang 100baseT4",
"3c905B Cyclone 100baseTx",
"3c575", /* Cardbus Boomerang */
};
/*
Theory of Operation
I. Board Compatibility
This device driver is designed for the 3Com FastEtherLink and FastEtherLink
XL, 3Com's PCI to 10/100baseT adapters. It also works with the 10Mbs
versions of the FastEtherLink cards. The supported product IDs are
3c590, 3c592, 3c595, 3c597, 3c900, 3c905
The ISA 3c515 is supported with a separate driver, 3c515.c, included with
the kernel source or available from
cesdis.gsfc.nasa.gov:/pub/linux/drivers/3c515.html
II. Board-specific settings
PCI bus devices are configured by the system at boot time, so no jumpers
need to be set on the board. The system BIOS should be set to assign the
PCI INTA signal to an otherwise unused system IRQ line. While it's
physically possible to shared PCI interrupt lines, the 1.2.0 kernel doesn't
support it.
III. Driver operation
The 3c59x series use an interface that's very similar to the previous 3c5x9
series. The primary interface is two programmed-I/O FIFOs, with an
alternate single-contiguous-region bus-master transfer (see next).
The 3c900 "Boomerang" series uses a full-bus-master interface with separate
lists of transmit and receive descriptors, similar to the AMD LANCE/PCnet,
DEC Tulip and Intel Speedo3. The first chip version retains a compatible
programmed-I/O interface that will be removed in the 'B' and subsequent
revisions.
One extension that is advertised in a very large font is that the adapters
are capable of being bus masters. On the Vortex chip this capability was
only for a single contiguous region making it far less useful than the full
bus master capability. There is a significant performance impact of taking
an extra interrupt or polling for the completion of each transfer, as well
as difficulty sharing the single transfer engine between the transmit and
receive threads. Using DMA transfers is a win only with large blocks or
with the flawed versions of the Intel Orion motherboard PCI controller.
The Boomerang chip's full-bus-master interface is useful, and has the
currently-unused advantages over other similar chips that queued transmit
packets may be reordered and receive buffer groups are associated with a
single frame.
With full-bus-master support, this driver uses a "RX_COPYBREAK" scheme.
Tather than a fixed intermediate receive buffer, this scheme allocates
full-sized skbuffs as receive buffers. The value RX_COPYBREAK is used as
the copying breakpoint: it is chosen to trade-off the memory wasted by
passing the full-sized skbuff to the queue layer for all frames vs. the
copying cost of copying a frame to a correctly-sized skbuff.
IIIC. Synchronization
The driver runs as two independent, single-threaded flows of control. One
is the send-packet routine, which enforces single-threaded use by the
dev->tbusy flag. The other thread is the interrupt handler, which is single
threaded by the hardware and other software.
IV. Notes
Thanks to Cameron Spitzer and Terry Murphy of 3Com for providing development
3c590, 3c595, and 3c900 boards.
The name "Vortex" is the internal 3Com project name for the PCI ASIC, and
the EISA version is called "Demon". According to Terry these names come
from rides at the local amusement park.
The new chips support both ethernet (1.5K) and FDDI (4.5K) packet sizes!
This driver only supports ethernet packets because of the skbuff allocation
limit of 4K.
*/
#define TCOM_VENDOR_ID 0x10B7 /* 3Com's manufacturer's ID. */
/* Operational definitions.
These are not used by other compilation units and thus are not
exported in a ".h" file.
First the windows. There are eight register windows, with the command
and status registers available in each.
*/
#define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD)
#define EL3_CMD 0x0e
#define EL3_STATUS 0x0e
/* The top five bits written to EL3_CMD are a command, the lower
11 bits are the parameter, if applicable.
Note that 11 parameters bits was fine for ethernet, but the new chip
can handle FDDI length frames (~4500 octets) and now parameters count
32-bit 'Dwords' rather than octets. */
enum vortex_cmd {
TotalReset = 0<<11, SelectWindow = 1<<11, StartCoax = 2<<11,
RxDisable = 3<<11, RxEnable = 4<<11, RxReset = 5<<11,
UpStall = 6<<11, UpUnstall = (6<<11)+1,
DownStall = (6<<11)+2, DownUnstall = (6<<11)+3,
RxDiscard = 8<<11, TxEnable = 9<<11, TxDisable = 10<<11, TxReset = 11<<11,
FakeIntr = 12<<11, AckIntr = 13<<11, SetIntrEnb = 14<<11,
SetStatusEnb = 15<<11, SetRxFilter = 16<<11, SetRxThreshold = 17<<11,
SetTxThreshold = 18<<11, SetTxStart = 19<<11,
StartDMAUp = 20<<11, StartDMADown = (20<<11)+1, StatsEnable = 21<<11,
StatsDisable = 22<<11, StopCoax = 23<<11,};
/* The SetRxFilter command accepts the following classes: */
enum RxFilter {
RxStation = 1, RxMulticast = 2, RxBroadcast = 4, RxProm = 8 };
/* Bits in the general status register. */
enum vortex_status {
IntLatch = 0x0001, HostError = 0x0002, TxComplete = 0x0004,
TxAvailable = 0x0008, RxComplete = 0x0010, RxEarly = 0x0020,
IntReq = 0x0040, StatsFull = 0x0080,
DMADone = 1<<8, DownComplete = 1<<9, UpComplete = 1<<10,
DMAInProgress = 1<<11, /* DMA controller is still busy.*/
CmdInProgress = 1<<12, /* EL3_CMD is still busy.*/
};
/* Register window 1 offsets, the window used in normal operation.
On the Vortex this window is always mapped at offsets 0x10-0x1f. */
enum Window1 {
TX_FIFO = 0x10, RX_FIFO = 0x10, RxErrors = 0x14,
RxStatus = 0x18, Timer=0x1A, TxStatus = 0x1B,
TxFree = 0x1C, /* Remaining free bytes in Tx buffer. */
};
enum Window0 {
Wn0EepromCmd = 10, /* Window 0: EEPROM command register. */
Wn0EepromData = 12, /* Window 0: EEPROM results register. */
IntrStatus=0x0E, /* Valid in all windows. */
};
enum Win0_EEPROM_bits {
EEPROM_Read = 0x80, EEPROM_WRITE = 0x40, EEPROM_ERASE = 0xC0,
EEPROM_EWENB = 0x30, /* Enable erasing/writing for 10 msec. */
EEPROM_EWDIS = 0x00, /* Disable EWENB before 10 msec timeout. */
};
/* EEPROM locations. */
enum eeprom_offset {
PhysAddr01=0, PhysAddr23=1, PhysAddr45=2, ModelID=3,
EtherLink3ID=7, IFXcvrIO=8, IRQLine=9,
NodeAddr01=10, NodeAddr23=11, NodeAddr45=12,
DriverTune=13, Checksum=15};
enum Window3 { /* Window 3: MAC/config bits. */
Wn3_Config=0, Wn3_MAC_Ctrl=6, Wn3_Options=8,
};
union wn3_config {
int i;
struct w3_config_fields {
unsigned int ram_size:3, ram_width:1, ram_speed:2, rom_size:2;
int pad8:8;
unsigned int ram_split:2, pad18:2, xcvr:4, autoselect:1;
int pad24:7;
} u;
};
enum Window4 { /* Window 4: Xcvr/media bits. */
Wn4_FIFODiag = 4, Wn4_NetDiag = 6, Wn4_PhysicalMgmt=8, Wn4_Media = 10,
};
enum Win4_Media_bits {
Media_SQE = 0x0008, /* Enable SQE error counting for AUI. */
Media_10TP = 0x00C0, /* Enable link beat and jabber for 10baseT. */
Media_Lnk = 0x0080, /* Enable just link beat for 100TX/100FX. */
Media_LnkBeat = 0x0800,
};
enum Window7 { /* Window 7: Bus Master control. */
Wn7_MasterAddr = 0, Wn7_MasterLen = 6, Wn7_MasterStatus = 12,
};
/* Boomerang bus master control registers. */
enum MasterCtrl {
PktStatus = 0x20, DownListPtr = 0x24, FragAddr = 0x28, FragLen = 0x2c,
TxFreeThreshold = 0x2f, UpPktStatus = 0x30, UpListPtr = 0x38,
};
/* The Rx and Tx descriptor lists.
Caution Alpha hackers: these types are 32 bits! Note also the 8 byte
alignment contraint on tx_ring[] and rx_ring[]. */
#define LAST_FRAG 0x80000000 /* Last Addr/Len pair in descriptor. */
struct boom_rx_desc {
u32 next; /* Last entry points to 0. */
s32 status;
u32 addr; /* Up to 63 addr/len pairs possible. */
s32 length; /* Set LAST_FRAG to indicate last pair. */
};
/* Values for the Rx status entry. */
enum rx_desc_status {
RxDComplete=0x00008000, RxDError=0x4000,
/* See boomerang_rx() for actual error bits */
IPChksumErr=1<<25, TCPChksumErr=1<<26, UDPChksumErr=1<<27,
IPChksumValid=1<<29, TCPChksumValid=1<<30, UDPChksumValid=1<<31,
};
struct boom_tx_desc {
u32 next; /* Last entry points to 0. */
s32 status; /* bits 0:12 length, others see below. */
u32 addr;
s32 length;
};
/* Values for the Tx status entry. */
enum tx_desc_status {
CRCDisable=0x2000, TxDComplete=0x8000,
AddIPChksum=0x02000000, AddTCPChksum=0x04000000, AddUDPChksum=0x08000000,
TxIntrUploaded=0x80000000, /* IRQ when in FIFO, but maybe not sent. */
};
/* Chip features we care about in vp->capabilities, read from the EEPROM. */
enum ChipCaps { CapBusMaster=0x20 };
struct vortex_private {
char devname[8]; /* "ethN" string, also for kernel debug. */
const char *product_name;
struct device *next_module;
/* The Rx and Tx rings are here to keep them quad-word-aligned. */
struct boom_rx_desc rx_ring[RX_RING_SIZE];
struct boom_tx_desc tx_ring[TX_RING_SIZE];
/* The addresses of transmit- and receive-in-place skbuffs. */
struct sk_buff* rx_skbuff[RX_RING_SIZE];
struct sk_buff* tx_skbuff[TX_RING_SIZE];
unsigned int cur_rx, cur_tx; /* The next free ring entry */
unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */
struct enet_statistics stats;
struct sk_buff *tx_skb; /* Packet being eaten by bus master ctrl. */
/* PCI configuration space information. */
u8 pci_bus, pci_dev_fn; /* PCI bus location, for power management. */
u16 pci_device_id;
/* The remainder are related to chip state, mostly media selection. */
int in_interrupt;
struct timer_list timer; /* Media selection timer. */
int options; /* User-settable misc. driver options. */
unsigned int
media_override:3, /* Passed-in media type. */
default_media:3, /* Read from the EEPROM/Wn3_Config. */
full_duplex:1, autoselect:1,
bus_master:1, /* Vortex can only do a fragment bus-m. */
full_bus_master_tx:1, full_bus_master_rx:2, /* Boomerang */
hw_csums:1, /* Has hardware checksums. */
tx_full:1;
u16 status_enable;
u16 available_media; /* From Wn3_Options. */
u16 capabilities, info1, info2; /* Various, from EEPROM. */
u16 advertising; /* NWay media advertisement */
unsigned char phys[2]; /* MII device addresses. */
};
/* The action to take with a media selection timer tick.
Note that we deviate from the 3Com order by checking 10base2 before AUI.
*/
enum xcvr_types {
XCVR_10baseT=0, XCVR_AUI, XCVR_10baseTOnly, XCVR_10base2, XCVR_100baseTx,
XCVR_100baseFx, XCVR_MII=6, XCVR_NWAY=8, XCVR_ExtMII=9, XCVR_Default=10,
};
static struct media_table {
char *name;
unsigned int media_bits:16, /* Bits to set in Wn4_Media register. */
mask:8, /* The transceiver-present bit in Wn3_Config.*/
next:8; /* The media type to try next. */
int wait; /* Time before we check media status. */
} media_tbl[] = {
{ "10baseT", Media_10TP,0x08, XCVR_10base2, (14*HZ)/10},
{ "10Mbs AUI", Media_SQE, 0x20, XCVR_Default, (1*HZ)/10},
{ "undefined", 0, 0x80, XCVR_10baseT, 10000},
{ "10base2", 0, 0x10, XCVR_AUI, (1*HZ)/10},
{ "100baseTX", Media_Lnk, 0x02, XCVR_100baseFx, (14*HZ)/10},
{ "100baseFX", Media_Lnk, 0x04, XCVR_MII, (14*HZ)/10},
{ "MII", 0, 0x41, XCVR_10baseT, 3*HZ },
{ "undefined", 0, 0x01, XCVR_10baseT, 10000},
{ "Autonegotiate", 0, 0x41, XCVR_10baseT, 3*HZ},
{ "MII-External", 0, 0x41, XCVR_10baseT, 3*HZ },
{ "Default", 0, 0xFF, XCVR_10baseT, 10000},
};
static int vortex_scan(struct device *dev);
static struct device *vortex_found_device(struct device *dev, int ioaddr,
int irq, int device_id,
int options, int card_idx);
static int vortex_probe1(struct device *dev);
static int vortex_open(struct device *dev);
static void mdio_sync(int ioaddr, int bits);
static int mdio_read(int ioaddr, int phy_id, int location);
#ifdef HAVE_PRIVATE_IOCTL
static void mdio_write(int ioaddr, int phy_id, int location, int value);
#endif
static void vortex_timer(unsigned long arg);
static int vortex_start_xmit(struct sk_buff *skb, struct device *dev);
static int boomerang_start_xmit(struct sk_buff *skb, struct device *dev);
static int vortex_rx(struct device *dev);
static int boomerang_rx(struct device *dev);
static void vortex_interrupt IRQ(int irq, void *dev_id, struct pt_regs *regs);
static int vortex_close(struct device *dev);
static void update_stats(int addr, struct device *dev);
static struct enet_statistics *vortex_get_stats(struct device *dev);
static void set_rx_mode(struct device *dev);
#ifdef HAVE_PRIVATE_IOCTL
static int vortex_ioctl(struct device *dev, struct ifreq *rq, int cmd);
#endif
#ifndef NEW_MULTICAST
static void set_multicast_list(struct device *dev, int num_addrs, void *addrs);
#endif
/* Unlike the other PCI cards the 59x cards don't need a large contiguous
memory region, so making the driver a loadable module is feasible.
Unfortunately maximizing the shared code between the integrated and
module version of the driver results in a complicated set of initialization
procedures.
init_module() -- modules / tc59x_init() -- built-in
The wrappers for vortex_scan()
vortex_scan() The common routine that scans for PCI and EISA cards
vortex_found_device() Allocate a device structure when we find a card.
Different versions exist for modules and built-in.
vortex_probe1() Fill in the device structure -- this is separated
so that the modules code can put it in dev->init.
*/
/* This driver uses 'options' to pass the media type, full-duplex flag, etc. */
/* Note: this is the only limit on the number of cards supported!! */
static int options[8] = { -1, -1, -1, -1, -1, -1, -1, -1,};
static int full_duplex[8] = {-1, -1, -1, -1, -1, -1, -1, -1};
/* A list of all installed Vortex devices, for removing the driver module. */
static struct device *root_vortex_dev = NULL;
#ifdef MODULE
/* Variables to work-around the Compaq PCI BIOS32 problem. */
static int compaq_ioaddr = 0, compaq_irq = 0, compaq_device_id = 0x5900;
static int debug = -1;
#ifdef CARDBUS
#include <pcmcia/driver_ops.h>
static dev_node_t *vortex_attach(dev_locator_t *loc)
{
u16 dev_id;
u32 io;
u8 bus, devfn, irq;
struct device *dev;
if (loc->bus != LOC_PCI) return NULL;
bus = loc->b.pci.bus; devfn = loc->b.pci.devfn;
printk(KERN_INFO "vortex_attach(bus %d, function %d)\n", bus, devfn);
pcibios_read_config_dword(bus, devfn, PCI_BASE_ADDRESS_0, &io);
pcibios_read_config_byte(bus, devfn, PCI_INTERRUPT_LINE, &irq);
pcibios_read_config_word(bus, devfn, PCI_DEVICE_ID, &dev_id);
io &= ~3;
dev = vortex_found_device(NULL, io, irq, dev_id, 0, -1);
if (dev) {
dev_node_t *node = kmalloc(sizeof(dev_node_t), GFP_KERNEL);
strcpy(node->dev_name, dev->name);
node->major = node->minor = 0;
node->next = NULL;
MOD_INC_USE_COUNT;
return node;
}
return NULL;
}
static void vortex_detach(dev_node_t *node)
{
struct device **devp, **next;
printk(KERN_INFO "vortex_detach(%s)\n", node->dev_name);
for (devp = &root_vortex_dev; *devp; devp = next) {
next = &((struct vortex_private *)(*devp)->priv)->next_module;
if (strcmp((*devp)->name, node->dev_name) == 0) break;
}
if (*devp) {
struct device *dev = *devp;
if (dev->flags & IFF_UP)
vortex_close(dev);
dev->flags &= ~(IFF_UP|IFF_RUNNING);
unregister_netdev(dev);
kfree(dev);
*devp = *next;
kfree(node);
MOD_DEC_USE_COUNT;
}
}
struct driver_operations vortex_ops = {
"3c59x_cb", vortex_attach, NULL, NULL, vortex_detach
};
#endif /* Cardbus support */
int
init_module(void)
{
if (debug >= 0)
vortex_debug = debug;
if (vortex_debug)
printk(version);
root_vortex_dev = NULL;
#ifdef CARDBUS
register_driver(&vortex_ops);
return 0;
#else
{
int cards_found = vortex_scan(0);
if (cards_found == 0)
printk("No 3Com Vortex/Boomerang cards found.\n");
return cards_found ? 0 : -ENODEV;
}
#endif
}
#else
int tc59x_probe(struct device *dev)
{
int cards_found = 0;
cards_found = vortex_scan(dev);
if (vortex_debug > 0 && cards_found)
printk(version);
return cards_found ? 0 : -ENODEV;
}
#endif /* not MODULE */
static int vortex_scan(struct device *dev)
{
int cards_found = 0;
/* Allow an EISA-only driver. */
#if defined(CONFIG_PCI) || (defined(MODULE) && !defined(NO_PCI))
/* Ideally we would detect all cards in slot order. That would
be best done a central PCI probe dispatch, which wouldn't work
well with the current structure. So instead we detect 3Com cards
in slot order. */
if (pcibios_present()) {
static int pci_index = 0;
unsigned char pci_bus, pci_device_fn;
for (;pci_index < 0xff; pci_index++) {
u8 pci_latency;
u16 pci_command, new_command, vendor, device;
int irq;
long ioaddr;
if (pcibios_find_class (PCI_CLASS_NETWORK_ETHERNET << 8,
pci_index, &pci_bus, &pci_device_fn)
!= PCIBIOS_SUCCESSFUL)
break;
pcibios_read_config_word(pci_bus, pci_device_fn,
PCI_VENDOR_ID, &vendor);
pcibios_read_config_word(pci_bus, pci_device_fn,
PCI_DEVICE_ID, &device);
pcibios_read_config_word(pci_bus, pci_device_fn,
PCI_COMMAND, &pci_command);
{
#if LINUX_VERSION_CODE >= 0x20155
struct pci_dev *pdev = pci_find_slot(pci_bus, pci_device_fn);
ioaddr = pdev->base_address[0];
irq = pdev->irq;
#else
u32 pci_ioaddr;
u8 pci_irq_line;
pcibios_read_config_byte(pci_bus, pci_device_fn,
PCI_INTERRUPT_LINE, &pci_irq_line);
pcibios_read_config_dword(pci_bus, pci_device_fn,
PCI_BASE_ADDRESS_0, &pci_ioaddr);
ioaddr = pci_ioaddr;
irq = pci_irq_line;
#endif
}
/* Remove I/O space marker in bit 0. */
ioaddr &= ~3;
if (vendor != TCOM_VENDOR_ID)
continue;
if (ioaddr == 0) {
printk(KERN_WARNING " A 3Com network adapter has been found, "
"however it has not been assigned an I/O address.\n"
" You may need to power-cycle the machine for this "
"device to work!\n");
continue;
}
if (check_region(ioaddr, VORTEX_TOTAL_SIZE))
continue;
/* Activate the card. */
new_command = pci_command | PCI_COMMAND_MASTER|PCI_COMMAND_IO;
if (pci_command != new_command) {
printk(KERN_INFO " The PCI BIOS has not enabled this"
" device! Updating PCI command %4.4x->%4.4x.\n",
pci_command, new_command);
pcibios_write_config_word(pci_bus, pci_device_fn,
PCI_COMMAND, new_command);
}
dev = vortex_found_device(dev, ioaddr, irq,
device, dev && dev->mem_start
? dev->mem_start : options[cards_found],
cards_found);
if (dev) {
struct vortex_private *vp = (struct vortex_private *)dev->priv;
/* Get and check the latency values. On the 3c590 series
the latency timer must be set to the maximum value to avoid
data corruption that occurs when the timer expires during
a transfer -- a bug in the Vortex chip only. */
u8 new_latency = (device&0xff00) == 0x5900 ? 248 : 32;
vp->pci_bus = pci_bus;
vp->pci_dev_fn = pci_device_fn;
vp->pci_device_id = device;
pcibios_read_config_byte(pci_bus, pci_device_fn,
PCI_LATENCY_TIMER, &pci_latency);
if (pci_latency < new_latency) {
printk(KERN_INFO "%s: Overriding PCI latency"
" timer (CFLT) setting of %d, new value is %d.\n",
dev->name, pci_latency, new_latency);
pcibios_write_config_byte(pci_bus, pci_device_fn,
PCI_LATENCY_TIMER, new_latency);
}
dev = 0;
cards_found++;
}
}
}
#endif /* NO_PCI */
/* Now check all slots of the EISA bus. */
if (EISA_bus) {
static int ioaddr = 0x1000;
for ( ; ioaddr < 0x9000; ioaddr += 0x1000) {
int device_id;
if (check_region(ioaddr, VORTEX_TOTAL_SIZE))
continue;
/* Check the standard EISA ID register for an encoded '3Com'. */
if (inw(ioaddr + 0xC80) != 0x6d50)
continue;
/* Check for a product that we support, 3c59{2,7} any rev. */
device_id = (inb(ioaddr + 0xC82)<<8) + inb(ioaddr + 0xC83);
if ((device_id & 0xFF00) != 0x5900)
continue;
vortex_found_device(dev, ioaddr, inw(ioaddr + 0xC88) >> 12,
device_id, dev && dev->mem_start
? dev->mem_start : options[cards_found],
cards_found);
dev = 0;
cards_found++;
}
}
#ifdef MODULE
/* Special code to work-around the Compaq PCI BIOS32 problem. */
if (compaq_ioaddr) {
vortex_found_device(dev, compaq_ioaddr, compaq_irq, compaq_device_id,
dev && dev->mem_start ? dev->mem_start
: options[cards_found], cards_found);
cards_found++;
dev = 0;
}
#endif
/* 3c515 cards are now supported by the 3c515.c driver. */
return cards_found;
}
static struct device *
vortex_found_device(struct device *dev, int ioaddr, int irq,
int device_id, int option, int card_idx)
{
struct vortex_private *vp;
const char *product_name;
int board_index = 0;
for (board_index = 0; product_ids[board_index]; board_index++) {
if (device_id == product_ids[board_index])
break;
}
/* Handle products we don't recognize, but might still work with. */
if (product_ids[board_index])
product_name = product_names[board_index];
else if ((device_id & 0xff00) == 0x5900)
product_name = "3c590 Vortex";
else if ((device_id & 0xfff0) == 0x9000)
product_name = "3c900";
else if ((device_id & 0xfff0) == 0x9050)
product_name = "3c905";
else {
printk(KERN_WARNING "Unknown 3Com PCI ethernet adapter type %4.4x detected:"
" not configured.\n", device_id);
return 0;
}
#ifdef MODULE
/* Allocate and fill new device structure. */
{
int dev_size = sizeof(struct device) +
sizeof(struct vortex_private) + 15; /* Pad for alignment */
dev = (struct device *) kmalloc(dev_size, GFP_KERNEL);
memset(dev, 0, dev_size);
}
/* Align the Rx and Tx ring entries. */
dev->priv = (void *)(((long)dev + sizeof(struct device) + 15) & ~15);
vp = (struct vortex_private *)dev->priv;
dev->name = vp->devname; /* An empty string. */
dev->base_addr = ioaddr;
dev->irq = irq;
dev->init = vortex_probe1;
vp->product_name = product_name;
vp->options = option;
if (card_idx >= 0) {
if (full_duplex[card_idx] >= 0)
vp->full_duplex = full_duplex[card_idx];
} else
vp->full_duplex = (option > 0 && (option & 0x10) ? 1 : 0);
if (option > 0) {
vp->media_override = ((option & 7) == XCVR_10baseTOnly) ?
XCVR_10baseT : option & 7;
vp->bus_master = (option & 16) ? 1 : 0;
} else {
vp->media_override = 7;
vp->bus_master = 0;
}
ether_setup(dev);
vp->next_module = root_vortex_dev;
root_vortex_dev = dev;
if (register_netdev(dev) != 0)
return 0;
#else /* not a MODULE */
if (dev) {
/* Caution: quad-word alignment required for rings! */
dev->priv = kmalloc(sizeof (struct vortex_private), GFP_KERNEL);
memset(dev->priv, 0, sizeof (struct vortex_private));
}
dev = init_etherdev(dev, sizeof(struct vortex_private));
dev->base_addr = ioaddr;
dev->irq = irq;
dev->mtu = mtu;
vp = (struct vortex_private *)dev->priv;
vp->product_name = product_name;
vp->options = option;
if (option >= 0) {
vp->media_override = ((option & 7) == 2) ? 0 : option & 7;
vp->full_duplex = (option & 8) ? 1 : 0;
vp->bus_master = (option & 16) ? 1 : 0;
} else {
vp->media_override = 7;
vp->full_duplex = 0;
vp->bus_master = 0;
}
vortex_probe1(dev);
#endif /* MODULE */
return dev;
}
static int vortex_probe1(struct device *dev)
{
int ioaddr = dev->base_addr;
struct vortex_private *vp = (struct vortex_private *)dev->priv;
u16 *ether_addr = (u16 *)dev->dev_addr;
unsigned int eeprom[0x40], checksum = 0; /* EEPROM contents */
int i;
printk(KERN_INFO "%s: 3Com %s at %#3x,",
dev->name, vp->product_name, ioaddr);
/* Read the station address from the EEPROM. */
EL3WINDOW(0);
for (i = 0; i < 0x40; i++) {
int timer;
#ifdef CARDBUS
outw(0x230 + i, ioaddr + Wn0EepromCmd);
#else
outw(EEPROM_Read + i, ioaddr + Wn0EepromCmd);
#endif
/* Pause for at least 162 us. for the read to take place. */
for (timer = 10; timer >= 0; timer--) {
udelay(162);
if ((inw(ioaddr + Wn0EepromCmd) & 0x8000) == 0)
break;
}
eeprom[i] = inw(ioaddr + Wn0EepromData);
}
for (i = 0; i < 0x18; i++)
checksum ^= eeprom[i];
checksum = (checksum ^ (checksum >> 8)) & 0xff;
if (checksum != 0x00) { /* Grrr, needless incompatible change 3Com. */
while (i < 0x21)
checksum ^= eeprom[i++];
checksum = (checksum ^ (checksum >> 8)) & 0xff;
}
if (checksum != 0x00)
printk(" ***INVALID CHECKSUM %4.4x*** ", checksum);
for (i = 0; i < 3; i++)
ether_addr[i] = htons(eeprom[i + 10]);
for (i = 0; i < 6; i++)
printk("%c%2.2x", i ? ':' : ' ', dev->dev_addr[i]);
printk(", IRQ %d\n", dev->irq);
/* Tell them about an invalid IRQ. */
if (vortex_debug && (dev->irq <= 0 || dev->irq >= NR_IRQS))
printk(KERN_WARNING " *** Warning: IRQ %d is unlikely to work! ***\n",
dev->irq);
/* Extract our information from the EEPROM data. */
vp->info1 = eeprom[13];
vp->info2 = eeprom[15];
vp->capabilities = eeprom[16];
if (vp->info1 & 0x8000)
vp->full_duplex = 1;
{
char *ram_split[] = {"5:3", "3:1", "1:1", "3:5"};
union wn3_config config;
EL3WINDOW(3);
vp->available_media = inw(ioaddr + Wn3_Options);
if ((vp->available_media & 0xff) == 0) /* Broken 3c916 */
vp->available_media = 0x40;
config.i = inl(ioaddr + Wn3_Config);
if (vortex_debug > 1)
printk(KERN_DEBUG " Internal config register is %4.4x, "
"transceivers %#x.\n", config.i, inw(ioaddr + Wn3_Options));
printk(KERN_INFO " %dK %s-wide RAM %s Rx:Tx split, %s%s interface.\n",
8 << config.u.ram_size,
config.u.ram_width ? "word" : "byte",
ram_split[config.u.ram_split],
config.u.autoselect ? "autoselect/" : "",
config.u.xcvr ? "NWay Autonegotiation" :
media_tbl[config.u.xcvr].name);
vp->default_media = config.u.xcvr;
vp->autoselect = config.u.autoselect;
}
if (vp->media_override != 7) {
printk(KERN_INFO " Media override to transceiver type %d (%s).\n",
vp->media_override, media_tbl[vp->media_override].name);
dev->if_port = vp->media_override;
} else
dev->if_port = vp->default_media;
if (dev->if_port == XCVR_MII) {
int phy, phy_idx = 0;
EL3WINDOW(4);
for (phy = 0; phy < 32 && phy_idx < sizeof(vp->phys); phy++) {
int mii_status;
mdio_sync(ioaddr, 32);
mii_status = mdio_read(ioaddr, phy, 1);
if (mii_status && mii_status != 0xffff) {
vp->phys[phy_idx++] = phy;
printk(KERN_INFO " MII transceiver found at address %d, status %4x.\n",
phy, mii_status);
mdio_sync(ioaddr, 32);
if ((mdio_read(ioaddr, phy, 1) & 0x0040) == 0)
mii_preamble_required = 1;
}
}
if (phy_idx == 0) {
printk(KERN_WARNING" ***WARNING*** No MII transceivers found!\n");
vp->phys[0] = 24;
} else {
vp->advertising = mdio_read(ioaddr, vp->phys[0], 4);
if (vp->full_duplex) {
/* Only advertise the FD media types. */
vp->advertising &= 0x015F;
mdio_write(ioaddr, vp->phys[0], 4, vp->advertising);
}
}
}
if (vp->capabilities & CapBusMaster) {
vp->full_bus_master_tx = 1;
printk(KERN_INFO" Enabling bus-master transmits and %s receives.\n",
(vp->info2 & 1) ? "early" : "whole-frame" );
vp->full_bus_master_rx = (vp->info2 & 1) ? 1 : 2;
}
/* We do a request_region() to register /proc/ioports info. */
request_region(ioaddr, VORTEX_TOTAL_SIZE, vp->product_name);
/* The 3c59x-specific entries in the device structure. */
dev->open = &vortex_open;
dev->hard_start_xmit = &vortex_start_xmit;
dev->stop = &vortex_close;
dev->get_stats = &vortex_get_stats;
#ifdef HAVE_PRIVATE_IOCTL
dev->do_ioctl = &vortex_ioctl;
#endif
#ifdef NEW_MULTICAST
dev->set_multicast_list = &set_rx_mode;
#else
dev->set_multicast_list = &set_multicast_list;
#endif
return 0;
}
static int
vortex_open(struct device *dev)
{
int ioaddr = dev->base_addr;
struct vortex_private *vp = (struct vortex_private *)dev->priv;
union wn3_config config;
int i;
/* Before initializing select the active media port. */
EL3WINDOW(3);
config.i = inl(ioaddr + Wn3_Config);
if (vp->media_override != 7) {
if (vortex_debug > 1)
printk(KERN_INFO "%s: Media override to transceiver %d (%s).\n",
dev->name, vp->media_override,
media_tbl[vp->media_override].name);
dev->if_port = vp->media_override;
} else if (vp->autoselect) {
/* Find first available media type, starting with 100baseTx. */
dev->if_port = XCVR_100baseTx;
while (! (vp->available_media & media_tbl[dev->if_port].mask))
dev->if_port = media_tbl[dev->if_port].next;
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Initial media type %s.\n",
dev->name, media_tbl[dev->if_port].name);
init_timer(&vp->timer);
vp->timer.expires = RUN_AT(media_tbl[dev->if_port].wait);
vp->timer.data = (unsigned long)dev;
vp->timer.function = &vortex_timer; /* timer handler */
add_timer(&vp->timer);
} else
dev->if_port = vp->default_media;
config.u.xcvr = dev->if_port;
outl(config.i, ioaddr + Wn3_Config);
if (dev->if_port == XCVR_MII) {
int mii_reg1, mii_reg5;
EL3WINDOW(4);
/* Read BMSR (reg1) only to clear old status. */
mii_reg1 = mdio_read(ioaddr, vp->phys[0], 1);
mii_reg5 = mdio_read(ioaddr, vp->phys[0], 5);
if (mii_reg5 == 0xffff || mii_reg5 == 0x0000)
; /* No MII device or no link partner report */
else if ((mii_reg5 & 0x0100) != 0 /* 100baseTx-FD */
|| (mii_reg5 & 0x00C0) == 0x0040) /* 10T-FD, but not 100-HD */
vp->full_duplex = 1;
if (vortex_debug > 1)
printk(KERN_INFO "%s: MII #%d status %4.4x, link partner capability %4.4x,"
" setting %s-duplex.\n", dev->name, vp->phys[0],
mii_reg1, mii_reg5, vp->full_duplex ? "full" : "half");
EL3WINDOW(3);
}
/* Set the full-duplex bit. */
outb(((vp->info1 & 0x8000) || vp->full_duplex ? 0x20 : 0) |
(dev->mtu > 1500 ? 0x40 : 0), ioaddr + Wn3_MAC_Ctrl);
if (vortex_debug > 1) {
printk(KERN_DEBUG "%s: vortex_open() InternalConfig %8.8x.\n",
dev->name, config.i);
}
outw(TxReset, ioaddr + EL3_CMD);
for (i = 2000; i >= 0 ; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
outw(RxReset, ioaddr + EL3_CMD);
/* Wait a few ticks for the RxReset command to complete. */
for (i = 2000; i >= 0 ; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
outw(SetStatusEnb | 0x00, ioaddr + EL3_CMD);
#ifdef SA_SHIRQ
/* Use the now-standard shared IRQ implementation. */
if (request_irq(dev->irq, &vortex_interrupt, SA_SHIRQ, dev->name, dev)) {
return -EAGAIN;
}
#else
if (dev->irq == 0 || irq2dev_map[dev->irq] != NULL)
return -EAGAIN;
irq2dev_map[dev->irq] = dev;
if (request_irq(dev->irq, &vortex_interrupt, 0, vp->product_name)) {
irq2dev_map[dev->irq] = NULL;
return -EAGAIN;
}
#endif
if (vortex_debug > 1) {
EL3WINDOW(4);
printk(KERN_DEBUG "%s: vortex_open() irq %d media status %4.4x.\n",
dev->name, dev->irq, inw(ioaddr + Wn4_Media));
}
/* Set the station address and mask in window 2 each time opened. */
EL3WINDOW(2);
for (i = 0; i < 6; i++)
outb(dev->dev_addr[i], ioaddr + i);
for (; i < 12; i+=2)
outw(0, ioaddr + i);
if (dev->if_port == XCVR_10base2)
/* Start the thinnet transceiver. We should really wait 50ms...*/
outw(StartCoax, ioaddr + EL3_CMD);
EL3WINDOW(4);
outw((inw(ioaddr + Wn4_Media) & ~(Media_10TP|Media_SQE)) |
media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
/* Switch to the stats window, and clear all stats by reading. */
outw(StatsDisable, ioaddr + EL3_CMD);
EL3WINDOW(6);
for (i = 0; i < 10; i++)
inb(ioaddr + i);
inw(ioaddr + 10);
inw(ioaddr + 12);
/* New: On the Vortex we must also clear the BadSSD counter. */
EL3WINDOW(4);
inb(ioaddr + 12);
/* ..and on the Boomerang we enable the extra statistics bits. */
outw(0x0040, ioaddr + Wn4_NetDiag);
/* Switch to register set 7 for normal use. */
EL3WINDOW(7);
if (vp->full_bus_master_rx) { /* Boomerang bus master. */
vp->cur_rx = vp->dirty_rx = 0;
/* Initialize the RxEarly register as recommended. */
outw(SetRxThreshold + (1536>>2), ioaddr + EL3_CMD);
outl(0x0020, ioaddr + PktStatus);
if (vortex_debug > 2)
printk(KERN_DEBUG "%s: Filling in the Rx ring.\n", dev->name);
for (i = 0; i < RX_RING_SIZE; i++) {
struct sk_buff *skb;
vp->rx_ring[i].next = virt_to_bus(&vp->rx_ring[i+1]);
vp->rx_ring[i].status = 0; /* Clear complete bit. */
vp->rx_ring[i].length = PKT_BUF_SZ | LAST_FRAG;
skb = DEV_ALLOC_SKB(PKT_BUF_SZ);
vp->rx_skbuff[i] = skb;
if (skb == NULL)
break; /* Bad news! */
skb->dev = dev; /* Mark as being used by this device. */
#if LINUX_VERSION_CODE >= 0x10300
skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
vp->rx_ring[i].addr = virt_to_bus(skb->tail);
#else
vp->rx_ring[i].addr = virt_to_bus(skb->data);
#endif
}
vp->rx_ring[i-1].next = virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */
outl(virt_to_bus(&vp->rx_ring[0]), ioaddr + UpListPtr);
}
if (vp->full_bus_master_tx) { /* Boomerang bus master Tx. */
dev->hard_start_xmit = &boomerang_start_xmit;
vp->cur_tx = vp->dirty_tx = 0;
outb(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold); /* Room for a packet. */
/* Clear the Tx ring. */
for (i = 0; i < TX_RING_SIZE; i++)
vp->tx_skbuff[i] = 0;
outl(0, ioaddr + DownListPtr);
}
/* Set reciever mode: presumably accept b-case and phys addr only. */
set_rx_mode(dev);
outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
vp->in_interrupt = 0;
dev->tbusy = 0;
dev->interrupt = 0;
dev->start = 1;
outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
/* Allow status bits to be seen. */
vp->status_enable = SetStatusEnb | HostError|IntReq|StatsFull|TxComplete|
(vp->full_bus_master_tx ? DownComplete : TxAvailable) |
(vp->full_bus_master_rx ? UpComplete : RxComplete) |
(vp->bus_master ? DMADone : 0);
outw(vp->status_enable, ioaddr + EL3_CMD);
/* Ack all pending events, and set active indicator mask. */
outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
ioaddr + EL3_CMD);
outw(SetIntrEnb | IntLatch | TxAvailable | RxComplete | StatsFull
| HostError | TxComplete
| (vp->bus_master ? DMADone : 0) | UpComplete | DownComplete,
ioaddr + EL3_CMD);
MOD_INC_USE_COUNT;
return 0;
}
static void vortex_timer(unsigned long data)
{
#ifdef AUTOMEDIA
struct device *dev = (struct device *)data;
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
unsigned long flags;
int ok = 0;
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media selection timer tick happened, %s.\n",
dev->name, media_tbl[dev->if_port].name);
save_flags(flags); cli(); {
int old_window = inw(ioaddr + EL3_CMD) >> 13;
int media_status;
EL3WINDOW(4);
media_status = inw(ioaddr + Wn4_Media);
switch (dev->if_port) {
case XCVR_10baseT: case XCVR_100baseTx: case XCVR_100baseFx:
if (media_status & Media_LnkBeat) {
ok = 1;
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media %s has link beat, %x.\n",
dev->name, media_tbl[dev->if_port].name, media_status);
} else if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media %s is has no link beat, %x.\n",
dev->name, media_tbl[dev->if_port].name, media_status);
break;
case XCVR_MII:
{
int mii_reg1 = mdio_read(ioaddr, vp->phys[0], 1);
int mii_reg5 = mdio_read(ioaddr, vp->phys[0], 5);
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: MII #%d status register is %4.4x, "
"link partner capability %4.4x.\n",
dev->name, vp->phys[0], mii_reg1, mii_reg5);
if (mii_reg1 & 0x0004)
ok = 1;
break;
}
default: /* Other media types handled by Tx timeouts. */
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media %s is has no indication, %x.\n",
dev->name, media_tbl[dev->if_port].name, media_status);
ok = 1;
}
if ( ! ok) {
union wn3_config config;
do {
dev->if_port = media_tbl[dev->if_port].next;
} while ( ! (vp->available_media & media_tbl[dev->if_port].mask));
if (dev->if_port == XCVR_Default) { /* Go back to default. */
dev->if_port = vp->default_media;
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media selection failing, using default "
"%s port.\n",
dev->name, media_tbl[dev->if_port].name);
} else {
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media selection failed, now trying "
"%s port.\n",
dev->name, media_tbl[dev->if_port].name);
vp->timer.expires = RUN_AT(media_tbl[dev->if_port].wait);
add_timer(&vp->timer);
}
outw((media_status & ~(Media_10TP|Media_SQE)) |
media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
EL3WINDOW(3);
config.i = inl(ioaddr + Wn3_Config);
config.u.xcvr = dev->if_port;
outl(config.i, ioaddr + Wn3_Config);
outw(dev->if_port == XCVR_10base2 ? StartCoax : StopCoax,
ioaddr + EL3_CMD);
}
EL3WINDOW(old_window);
} restore_flags(flags);
if (vortex_debug > 1)
printk(KERN_DEBUG "%s: Media selection timer finished, %s.\n",
dev->name, media_tbl[dev->if_port].name);
#endif /* AUTOMEDIA*/
return;
}
static void vortex_tx_timeout(struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
int j;
printk(KERN_ERR "%s: transmit timed out, tx_status %2.2x status %4.4x.\n",
dev->name, inb(ioaddr + TxStatus),
inw(ioaddr + EL3_STATUS));
/* Slight code bloat to be user friendly. */
if ((inb(ioaddr + TxStatus) & 0x88) == 0x88)
printk(KERN_ERR "%s: Transmitter encountered 16 collisions --"
" network cable problem?\n", dev->name);
if (inw(ioaddr + EL3_STATUS) & IntLatch) {
printk(KERN_ERR "%s: Interrupt posted but not delivered --"
" IRQ blocked by another device?\n", dev->name);
/* Bad idea here.. but we might as well handle a few events. */
vortex_interrupt IRQ(dev->irq, dev, 0);
}
outw(TxReset, ioaddr + EL3_CMD);
for (j = 200; j >= 0 ; j--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
#if ! defined(final_version) && LINUX_VERSION_CODE >= 0x10300
if (vp->full_bus_master_tx) {
int i;
printk(KERN_DEBUG " Flags; bus-master %d, full %d; dirty %d "
"current %d.\n",
vp->full_bus_master_tx, vp->tx_full, vp->dirty_tx, vp->cur_tx);
printk(KERN_DEBUG " Transmit list %8.8x vs. %p.\n",
inl(ioaddr + DownListPtr),
&vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]);
for (i = 0; i < TX_RING_SIZE; i++) {
printk(KERN_DEBUG " %d: @%p length %8.8x status %8.8x\n", i,
&vp->tx_ring[i],
vp->tx_ring[i].length,
vp->tx_ring[i].status);
}
}
#endif
vp->stats.tx_errors++;
if (vp->full_bus_master_tx) {
if (vortex_debug > 0)
printk(KERN_DEBUG "%s: Resetting the Tx ring pointer.\n",
dev->name);
if (vp->cur_tx - vp->dirty_tx > 0 && inl(ioaddr + DownListPtr) == 0)
outl(virt_to_bus(&vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]),
ioaddr + DownListPtr);
if (vp->tx_full && (vp->cur_tx - vp->dirty_tx <= TX_RING_SIZE - 1)) {
vp->tx_full = 0;
clear_bit(0, (void*)&dev->tbusy);
}
outb(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold);
outw(DownUnstall, ioaddr + EL3_CMD);
} else
vp->stats.tx_dropped++;
/* Issue Tx Enable */
outw(TxEnable, ioaddr + EL3_CMD);
dev->trans_start = jiffies;
/* Switch to register set 7 for normal use. */
EL3WINDOW(7);
}
/*
* Handle uncommon interrupt sources. This is a separate routine to minimize
* the cache impact.
*/
static void
vortex_error(struct device *dev, int status)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
int do_tx_reset = 0;
int i;
if (status & TxComplete) { /* Really "TxError" for us. */
unsigned char tx_status = inb(ioaddr + TxStatus);
/* Presumably a tx-timeout. We must merely re-enable. */
if (vortex_debug > 2
|| (tx_status != 0x88 && vortex_debug > 0))
printk(KERN_DEBUG"%s: Transmit error, Tx status register %2.2x.\n",
dev->name, tx_status);
if (tx_status & 0x14) vp->stats.tx_fifo_errors++;
if (tx_status & 0x38) vp->stats.tx_aborted_errors++;
outb(0, ioaddr + TxStatus);
if (tx_status & 0x30)
do_tx_reset = 1;
else /* Merely re-enable the transmitter. */
outw(TxEnable, ioaddr + EL3_CMD);
}
if (status & RxEarly) { /* Rx early is unused. */
vortex_rx(dev);
outw(AckIntr | RxEarly, ioaddr + EL3_CMD);
}
if (status & StatsFull) { /* Empty statistics. */
static int DoneDidThat = 0;
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: Updating stats.\n", dev->name);
update_stats(ioaddr, dev);
/* HACK: Disable statistics as an interrupt source. */
/* This occurs when we have the wrong media type! */
if (DoneDidThat == 0 &&
inw(ioaddr + EL3_STATUS) & StatsFull) {
printk(KERN_WARNING "%s: Updating statistics failed, disabling "
"stats as an interrupt source.\n", dev->name);
EL3WINDOW(5);
outw(SetIntrEnb | (inw(ioaddr + 10) & ~StatsFull), ioaddr + EL3_CMD);
EL3WINDOW(7);
DoneDidThat++;
}
}
if (status & IntReq) /* Restore all interrupt sources. */
outw(ioaddr + EL3_CMD, vp->status_enable);
if (status & HostError) {
u16 fifo_diag;
EL3WINDOW(4);
fifo_diag = inw(ioaddr + Wn4_FIFODiag);
if (vortex_debug > 0)
printk(KERN_ERR "%s: Host error, FIFO diagnostic register %4.4x.\n",
dev->name, fifo_diag);
/* Adapter failure requires Tx/Rx reset and reinit. */
if (vp->full_bus_master_tx) {
outw(TotalReset | 0xff, ioaddr + EL3_CMD);
for (i = 2000; i >= 0 ; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
/* Re-enable the receiver. */
outw(RxEnable, ioaddr + EL3_CMD);
outw(TxEnable, ioaddr + EL3_CMD);
} else if (fifo_diag & 0x0400)
do_tx_reset = 1;
if (fifo_diag & 0x3000) {
outw(RxReset, ioaddr + EL3_CMD);
for (i = 2000; i >= 0 ; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
/* Set the Rx filter to the current state. */
set_rx_mode(dev);
outw(RxEnable, ioaddr + EL3_CMD); /* Re-enable the receiver. */
outw(AckIntr | HostError, ioaddr + EL3_CMD);
}
}
if (do_tx_reset) {
int j;
outw(TxReset, ioaddr + EL3_CMD);
for (j = 200; j >= 0 ; j--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
outw(TxEnable, ioaddr + EL3_CMD);
}
}
static int
vortex_start_xmit(struct sk_buff *skb, struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
if (test_and_set_bit(0, (void*)&dev->tbusy) != 0) {
if (jiffies - dev->trans_start >= TX_TIMEOUT)
vortex_tx_timeout(dev);
return 1;
}
/* Put out the doubleword header... */
outl(skb->len, ioaddr + TX_FIFO);
#ifdef VORTEX_BUS_MASTER
if (vp->bus_master) {
/* Set the bus-master controller to transfer the packet. */
outl(virt_to_bus(skb->data), ioaddr + Wn7_MasterAddr);
outw((skb->len + 3) & ~3, ioaddr + Wn7_MasterLen);
vp->tx_skb = skb;
outw(StartDMADown, ioaddr + EL3_CMD);
/* dev->tbusy will be cleared at the DMADone interrupt. */
} else {
/* ... and the packet rounded to a doubleword. */
outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
DEV_FREE_SKB(skb);
if (inw(ioaddr + TxFree) > 1536) {
clear_bit(0, (void*)&dev->tbusy);
} else
/* Interrupt us when the FIFO has room for max-sized packet. */
outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
}
#else
/* ... and the packet rounded to a doubleword. */
outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
DEV_FREE_SKB(skb);
if (inw(ioaddr + TxFree) > 1536) {
clear_bit(0, (void*)&dev->tbusy);
} else
/* Interrupt us when the FIFO has room for max-sized packet. */
outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
#endif /* bus master */
dev->trans_start = jiffies;
/* Clear the Tx status stack. */
{
int tx_status;
int i = 32;
while (--i > 0 && (tx_status = inb(ioaddr + TxStatus)) > 0) {
if (tx_status & 0x3C) { /* A Tx-disabling error occurred. */
if (vortex_debug > 2)
printk(KERN_DEBUG "%s: Tx error, status %2.2x.\n",
dev->name, tx_status);
if (tx_status & 0x04) vp->stats.tx_fifo_errors++;
if (tx_status & 0x38) vp->stats.tx_aborted_errors++;
if (tx_status & 0x30) {
int j;
outw(TxReset, ioaddr + EL3_CMD);
for (j = 200; j >= 0 ; j--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
}
outw(TxEnable, ioaddr + EL3_CMD);
}
outb(0x00, ioaddr + TxStatus); /* Pop the status stack. */
}
}
return 0;
}
static int
boomerang_start_xmit(struct sk_buff *skb, struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
if (test_and_set_bit(0, (void*)&dev->tbusy) != 0) {
if (jiffies - dev->trans_start >= TX_TIMEOUT)
vortex_tx_timeout(dev);
return 1;
} else {
/* Calculate the next Tx descriptor entry. */
int entry = vp->cur_tx % TX_RING_SIZE;
struct boom_tx_desc *prev_entry =
&vp->tx_ring[(vp->cur_tx-1) % TX_RING_SIZE];
unsigned long flags;
int i;
if (vortex_debug > 3)
printk(KERN_DEBUG "%s: Trying to send a packet, Tx index %d.\n",
dev->name, vp->cur_tx);
if (vp->tx_full) {
if (vortex_debug >0)
printk(KERN_WARNING "%s: Tx Ring full, refusing to send buffer.\n",
dev->name);
return 1;
}
/* end change 06/25/97 M. Sievers */
vp->tx_skbuff[entry] = skb;
vp->tx_ring[entry].next = 0;
vp->tx_ring[entry].addr = virt_to_bus(skb->data);
vp->tx_ring[entry].length = skb->len | LAST_FRAG;
vp->tx_ring[entry].status = skb->len | TxIntrUploaded;
save_flags(flags);
cli();
outw(DownStall, ioaddr + EL3_CMD);
/* Wait for the stall to complete. */
for (i = 600; i >= 0 ; i--)
if ( (inw(ioaddr + EL3_STATUS) & CmdInProgress) == 0)
break;
prev_entry->next = virt_to_bus(&vp->tx_ring[entry]);
if (inl(ioaddr + DownListPtr) == 0) {
outl(virt_to_bus(&vp->tx_ring[entry]), ioaddr + DownListPtr);
queued_packet++;
}
outw(DownUnstall, ioaddr + EL3_CMD);
restore_flags(flags);
vp->cur_tx++;
if (vp->cur_tx - vp->dirty_tx > TX_RING_SIZE - 1)
vp->tx_full = 1;
else { /* Clear previous interrupt enable. */
prev_entry->status &= ~TxIntrUploaded;
clear_bit(0, (void*)&dev->tbusy);
}
dev->trans_start = jiffies;
return 0;
}
}
/* The interrupt handler does all of the Rx thread work and cleans up
after the Tx thread. */
static void vortex_interrupt IRQ(int irq, void *dev_id, struct pt_regs *regs)
{
#ifdef SA_SHIRQ /* Use the now-standard shared IRQ implementation. */
struct device *dev = dev_id;
#else
struct device *dev = (struct device *)(irq2dev_map[irq]);
#endif
struct vortex_private *vp;
int ioaddr, status;
int latency;
int work_done = max_interrupt_work;
vp = (struct vortex_private *)dev->priv;
if (test_and_set_bit(0, (void*)&vp->in_interrupt)) {
printk(KERN_ERR "%s: Re-entering the interrupt handler.\n", dev->name);
return;
}
dev->interrupt = 1;
ioaddr = dev->base_addr;
latency = inb(ioaddr + Timer);
status = inw(ioaddr + EL3_STATUS);
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: interrupt, status %4.4x, latency %d ticks.\n",
dev->name, status, latency);
do {
if (vortex_debug > 5)
printk(KERN_DEBUG "%s: In interrupt loop, status %4.4x.\n",
dev->name, status);
if (status & RxComplete)
vortex_rx(dev);
if (status & UpComplete) {
outw(AckIntr | UpComplete, ioaddr + EL3_CMD);
boomerang_rx(dev);
}
if (status & TxAvailable) {
if (vortex_debug > 5)
printk(KERN_DEBUG " TX room bit was handled.\n");
/* There's room in the FIFO for a full-sized packet. */
outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
clear_bit(0, (void*)&dev->tbusy);
mark_bh(NET_BH);
}
if (status & DownComplete) {
unsigned int dirty_tx = vp->dirty_tx;
while (vp->cur_tx - dirty_tx > 0) {
int entry = dirty_tx % TX_RING_SIZE;
if (inl(ioaddr + DownListPtr) ==
virt_to_bus(&vp->tx_ring[entry]))
break; /* It still hasn't been processed. */
if (vp->tx_skbuff[entry]) {
DEV_FREE_SKB(vp->tx_skbuff[entry]);
vp->tx_skbuff[entry] = 0;
}
/* vp->stats.tx_packets++; Counted below. */
dirty_tx++;
}
vp->dirty_tx = dirty_tx;
outw(AckIntr | DownComplete, ioaddr + EL3_CMD);
if (vp->tx_full && (vp->cur_tx - dirty_tx <= TX_RING_SIZE - 1)) {
vp->tx_full= 0;
clear_bit(0, (void*)&dev->tbusy);
mark_bh(NET_BH);
}
}
#ifdef VORTEX_BUS_MASTER
if (status & DMADone) {
outw(0x1000, ioaddr + Wn7_MasterStatus); /* Ack the event. */
clear_bit(0, (void*)&dev->tbusy);
DEV_FREE_SKB(vp->tx_skb); /* Release the transfered buffer */
mark_bh(NET_BH);
}
#endif
/* Check for all uncommon interrupts at once. */
if (status & (HostError | RxEarly | StatsFull | TxComplete | IntReq))
vortex_error(dev, status);
if (--work_done < 0) {
if ((status & (0x7fe - (UpComplete | DownComplete))) == 0) {
/* Just ack these and return. */
outw(AckIntr | UpComplete | DownComplete, ioaddr + EL3_CMD);
} else {
printk(KERN_WARNING "%s: Too much work in interrupt, status "
"%4.4x. Temporarily disabling functions (%4.4x).\n",
dev->name, status, SetStatusEnb | ((~status) & 0x7FE));
/* Disable all pending interrupts. */
outw(SetStatusEnb | ((~status) & 0x7FE), ioaddr + EL3_CMD);
outw(AckIntr | 0x7FF, ioaddr + EL3_CMD);
/* Set a timer to reenable interrupts. */
break;
}
}
/* Acknowledge the IRQ. */
outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
} while ((status = inw(ioaddr + EL3_STATUS)) & (IntLatch | RxComplete));
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: exiting interrupt, status %4.4x.\n",
dev->name, status);
dev->interrupt = 0;
clear_bit(0, (void*)&vp->in_interrupt);
return;
}
static int
vortex_rx(struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
int i;
short rx_status;
if (vortex_debug > 5)
printk(KERN_DEBUG" In rx_packet(), status %4.4x, rx_status %4.4x.\n",
inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
while ((rx_status = inw(ioaddr + RxStatus)) > 0) {
if (rx_status & 0x4000) { /* Error, update stats. */
unsigned char rx_error = inb(ioaddr + RxErrors);
if (vortex_debug > 2)
printk(KERN_DEBUG " Rx error: status %2.2x.\n", rx_error);
vp->stats.rx_errors++;
if (rx_error & 0x01) vp->stats.rx_over_errors++;
if (rx_error & 0x02) vp->stats.rx_length_errors++;
if (rx_error & 0x04) vp->stats.rx_frame_errors++;
if (rx_error & 0x08) vp->stats.rx_crc_errors++;
if (rx_error & 0x10) vp->stats.rx_length_errors++;
} else {
/* The packet length: up to 4.5K!. */
int pkt_len = rx_status & 0x1fff;
struct sk_buff *skb;
skb = DEV_ALLOC_SKB(pkt_len + 5);
if (vortex_debug > 4)
printk(KERN_DEBUG "Receiving packet size %d status %4.4x.\n",
pkt_len, rx_status);
if (skb != NULL) {
skb->dev = dev;
#if LINUX_VERSION_CODE >= 0x10300
skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
/* 'skb_put()' points to the start of sk_buff data area. */
insl(ioaddr + RX_FIFO, skb_put(skb, pkt_len),
(pkt_len + 3) >> 2);
outw(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
skb->protocol = eth_type_trans(skb, dev);
#else
skb->len = pkt_len;
/* 'skb->data' points to the start of sk_buff data area. */
insl(ioaddr + RX_FIFO, skb->data, (pkt_len + 3) >> 2);
outw(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
#endif /* KERNEL_1_3_0 */
netif_rx(skb);
dev->last_rx = jiffies;
vp->stats.rx_packets++;
/* Wait a limited time to go to next packet. */
for (i = 200; i >= 0; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
continue;
} else if (vortex_debug)
printk(KERN_NOTICE "%s: No memory to allocate a sk_buff of "
"size %d.\n", dev->name, pkt_len);
}
outw(RxDiscard, ioaddr + EL3_CMD);
vp->stats.rx_dropped++;
/* Wait a limited time to skip this packet. */
for (i = 200; i >= 0; i--)
if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
break;
}
return 0;
}
static int
boomerang_rx(struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int entry = vp->cur_rx % RX_RING_SIZE;
int ioaddr = dev->base_addr;
int rx_status;
int rx_work_limit = vp->dirty_rx + RX_RING_SIZE - vp->cur_rx;
if (vortex_debug > 5)
printk(KERN_DEBUG " In boomerang_rx(), status %4.4x, rx_status "
"%4.4x.\n",
inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
while ((rx_status = vp->rx_ring[entry].status) & RxDComplete) {
if (rx_status & RxDError) { /* Error, update stats. */
unsigned char rx_error = rx_status >> 16;
if (vortex_debug > 2)
printk(KERN_DEBUG " Rx error: status %2.2x.\n", rx_error);
vp->stats.rx_errors++;
if (rx_error & 0x01) vp->stats.rx_over_errors++;
if (rx_error & 0x02) vp->stats.rx_length_errors++;
if (rx_error & 0x04) vp->stats.rx_frame_errors++;
if (rx_error & 0x08) vp->stats.rx_crc_errors++;
if (rx_error & 0x10) vp->stats.rx_length_errors++;
} else {
/* The packet length: up to 4.5K!. */
int pkt_len = rx_status & 0x1fff;
struct sk_buff *skb;
if (vortex_debug > 4)
printk(KERN_DEBUG "Receiving packet size %d status %4.4x.\n",
pkt_len, rx_status);
/* Check if the packet is long enough to just accept without
copying to a properly sized skbuff. */
if (pkt_len < rx_copybreak
&& (skb = DEV_ALLOC_SKB(pkt_len + 2)) != 0) {
skb->dev = dev;
#if LINUX_VERSION_CODE >= 0x10300
skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
/* 'skb_put()' points to the start of sk_buff data area. */
memcpy(skb_put(skb, pkt_len),
bus_to_virt(vp->rx_ring[entry].addr),
pkt_len);
#else
memcpy(skb->data, bus_to_virt(vp->rx_ring[entry].addr), pkt_len);
skb->len = pkt_len;
#endif
rx_copy++;
} else{
void *temp;
/* Pass up the skbuff already on the Rx ring. */
skb = vp->rx_skbuff[entry];
vp->rx_skbuff[entry] = NULL;
#if LINUX_VERSION_CODE >= 0x10300
temp = skb_put(skb, pkt_len);
#else
temp = skb->data;
#endif
/* Remove this checking code for final release. */
if (bus_to_virt(vp->rx_ring[entry].addr) != temp)
printk(KERN_ERR "%s: Warning -- the skbuff addresses do not match"
" in boomerang_rx: %p vs. %p.\n", dev->name,
bus_to_virt(vp->rx_ring[entry].addr), temp);
rx_nocopy++;
}
#if LINUX_VERSION_CODE > 0x10300
skb->protocol = eth_type_trans(skb, dev);
#ifndef OSKIT
{ /* Use hardware checksum info. */
int csum_bits = rx_status & 0xee000000;
if (csum_bits &&
(csum_bits == (IPChksumValid | TCPChksumValid) ||
csum_bits == (IPChksumValid | UDPChksumValid))) {
skb->ip_summed = CHECKSUM_UNNECESSARY;
rx_csumhits++;
}
}
#endif
#else
skb->len = pkt_len;
#endif
netif_rx(skb);
dev->last_rx = jiffies;
vp->stats.rx_packets++;
}
entry = (++vp->cur_rx) % RX_RING_SIZE;
if (--rx_work_limit < 0)
break;
}
/* Refill the Rx ring buffers. */
for (; vp->dirty_rx < vp->cur_rx; vp->dirty_rx++) {
struct sk_buff *skb;
entry = vp->dirty_rx % RX_RING_SIZE;
if (vp->rx_skbuff[entry] == NULL) {
skb = DEV_ALLOC_SKB(PKT_BUF_SZ);
if (skb == NULL)
break; /* Bad news! */
skb->dev = dev; /* Mark as being used by this device. */
#if LINUX_VERSION_CODE > 0x10300
skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
vp->rx_ring[entry].addr = virt_to_bus(skb->tail);
#else
vp->rx_ring[entry].addr = virt_to_bus(skb->data);
#endif
vp->rx_skbuff[entry] = skb;
}
vp->rx_ring[entry].status = 0; /* Clear complete bit. */
outw(UpUnstall, ioaddr + EL3_CMD);
}
return 0;
}
static int
vortex_close(struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
int i;
dev->start = 0;
dev->tbusy = 1;
if (vortex_debug > 1) {
printk(KERN_DEBUG"%s: vortex_close() status %4.4x, Tx status %2.2x.\n",
dev->name, inw(ioaddr + EL3_STATUS), inb(ioaddr + TxStatus));
printk(KERN_DEBUG "%s: vortex close stats: rx_nocopy %d rx_copy %d"
" tx_queued %d Rx pre-checksummed %d.\n",
dev->name, rx_nocopy, rx_copy, queued_packet, rx_csumhits);
}
del_timer(&vp->timer);
/* Turn off statistics ASAP. We update vp->stats below. */
outw(StatsDisable, ioaddr + EL3_CMD);
/* Disable the receiver and transmitter. */
outw(RxDisable, ioaddr + EL3_CMD);
outw(TxDisable, ioaddr + EL3_CMD);
if (dev->if_port == XCVR_10base2)
/* Turn off thinnet power. Green! */
outw(StopCoax, ioaddr + EL3_CMD);
#ifdef SA_SHIRQ
free_irq(dev->irq, dev);
#else
free_irq(dev->irq);
irq2dev_map[dev->irq] = 0;
#endif
outw(SetIntrEnb | 0x0000, ioaddr + EL3_CMD);
update_stats(ioaddr, dev);
if (vp->full_bus_master_rx) { /* Free Boomerang bus master Rx buffers. */
outl(0, ioaddr + UpListPtr);
for (i = 0; i < RX_RING_SIZE; i++)
if (vp->rx_skbuff[i]) {
#ifndef OSKIT
#if LINUX_VERSION_CODE < 0x20100
vp->rx_skbuff[i]->free = 1;
#endif
#endif
DEV_FREE_SKB(vp->rx_skbuff[i]);
vp->rx_skbuff[i] = 0;
}
}
if (vp->full_bus_master_tx) { /* Free Boomerang bus master Tx buffers. */
outl(0, ioaddr + DownListPtr);
for (i = 0; i < TX_RING_SIZE; i++)
if (vp->tx_skbuff[i]) {
DEV_FREE_SKB(vp->tx_skbuff[i]);
vp->tx_skbuff[i] = 0;
}
}
MOD_DEC_USE_COUNT;
return 0;
}
static struct enet_statistics *
vortex_get_stats(struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
unsigned long flags;
if (dev->start) {
save_flags(flags);
cli();
update_stats(dev->base_addr, dev);
restore_flags(flags);
}
return &vp->stats;
}
/* Update statistics.
Unlike with the EL3 we need not worry about interrupts changing
the window setting from underneath us, but we must still guard
against a race condition with a StatsUpdate interrupt updating the
table. This is done by checking that the ASM (!) code generated uses
atomic updates with '+='.
*/
static void update_stats(int ioaddr, struct device *dev)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
/* Unlike the 3c5x9 we need not turn off stats updates while reading. */
/* Switch to the stats window, and read everything. */
EL3WINDOW(6);
vp->stats.tx_carrier_errors += inb(ioaddr + 0);
vp->stats.tx_heartbeat_errors += inb(ioaddr + 1);
/* Multiple collisions. */ inb(ioaddr + 2);
vp->stats.collisions += inb(ioaddr + 3);
vp->stats.tx_window_errors += inb(ioaddr + 4);
vp->stats.rx_fifo_errors += inb(ioaddr + 5);
vp->stats.tx_packets += inb(ioaddr + 6);
vp->stats.tx_packets += (inb(ioaddr + 9)&0x30) << 4;
/* Rx packets */ inb(ioaddr + 7); /* Must read to clear */
/* Tx deferrals */ inb(ioaddr + 8);
/* Don't bother with register 9, an extension of registers 6&7.
If we do use the 6&7 values the atomic update assumption above
is invalid. */
inw(ioaddr + 10); /* Total Rx and Tx octets. */
inw(ioaddr + 12);
/* New: On the Vortex we must also clear the BadSSD counter. */
EL3WINDOW(4);
inb(ioaddr + 12);
/* We change back to window 7 (not 1) with the Vortex. */
EL3WINDOW(7);
return;
}
#ifdef HAVE_PRIVATE_IOCTL
static int vortex_ioctl(struct device *dev, struct ifreq *rq, int cmd)
{
struct vortex_private *vp = (struct vortex_private *)dev->priv;
int ioaddr = dev->base_addr;
u16 *data = (u16 *)&rq->ifr_data;
int phy = vp->phys[0] & 0x1f;
if (vortex_debug > 2)
printk(KERN_DEBUG "%s: In ioct(%-.6s, %#4.4x) %4.4x %4.4x %4.4x %4.4x.\n",
dev->name, rq->ifr_ifrn.ifrn_name, cmd,
data[0], data[1], data[2], data[3]);
switch(cmd) {
case SIOCDEVPRIVATE: /* Get the address of the PHY in use. */
data[0] = phy;
case SIOCDEVPRIVATE+1: /* Read the specified MII register. */
EL3WINDOW(4);
data[3] = mdio_read(ioaddr, data[0] & 0x1f, data[1] & 0x1f);
return 0;
case SIOCDEVPRIVATE+2: /* Write the specified MII register */
if (!suser())
return -EPERM;
mdio_write(ioaddr, data[0] & 0x1f, data[1] & 0x1f, data[2]);
return 0;
default:
return -EOPNOTSUPP;
}
}
#endif /* HAVE_PRIVATE_IOCTL */
/* This new version of set_rx_mode() supports v1.4 kernels.
The Vortex chip has no documented multicast filter, so the only
multicast setting is to receive all multicast frames. At least
the chip has a very clean way to set the mode, unlike many others. */
static void
set_rx_mode(struct device *dev)
{
int ioaddr = dev->base_addr;
int new_mode;
if (dev->flags & IFF_PROMISC) {
if (vortex_debug > 0)
printk(KERN_NOTICE "%s: Setting promiscuous mode.\n", dev->name);
new_mode = SetRxFilter|RxStation|RxMulticast|RxBroadcast|RxProm;
} else if ((dev->mc_list) || (dev->flags & IFF_ALLMULTI)) {
new_mode = SetRxFilter|RxStation|RxMulticast|RxBroadcast;
} else
new_mode = SetRxFilter | RxStation | RxBroadcast;
outw(new_mode, ioaddr + EL3_CMD);
}
#ifndef NEW_MULTICAST
/* The old interface to set the Rx mode. */
static void
set_multicast_list(struct device *dev, int num_addrs, void *addrs)
{
set_rx_mode(dev);
}
#endif
/* MII transceiver control section.
Read and write the MII registers using software-generated serial
MDIO protocol. See the MII specifications or DP83840A data sheet
for details. */
/* The maximum data clock rate is 2.5 Mhz. The minimum timing is usually
met by back-to-back PCI I/O cycles, but we insert a delay to avoid
"overclocking" issues. */
#define mdio_delay() udelay(1)
#define MDIO_SHIFT_CLK 0x01
#define MDIO_DIR_WRITE 0x04
#define MDIO_DATA_WRITE0 (0x00 | MDIO_DIR_WRITE)
#define MDIO_DATA_WRITE1 (0x02 | MDIO_DIR_WRITE)
#define MDIO_DATA_READ 0x02
#define MDIO_ENB_IN 0x00
/* Generate the preamble required for initial synchronization and
a few older transceivers. */
static void mdio_sync(int ioaddr, int bits)
{
int mdio_addr = ioaddr + Wn4_PhysicalMgmt;
/* Establish sync by sending at least 32 logic ones. */
while (-- bits >= 0) {
outw(MDIO_DATA_WRITE1, mdio_addr);
mdio_delay();
outw(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
}
static int mdio_read(int ioaddr, int phy_id, int location)
{
int i;
int read_cmd = (0xf6 << 10) | (phy_id << 5) | location;
unsigned int retval = 0;
int mdio_addr = ioaddr + Wn4_PhysicalMgmt;
if (mii_preamble_required)
mdio_sync(ioaddr, 32);
/* Shift the read command bits out. */
for (i = 14; i >= 0; i--) {
int dataval = (read_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
outw(dataval, mdio_addr);
mdio_delay();
outw(dataval | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
/* Read the two transition, 16 data, and wire-idle bits. */
for (i = 19; i > 0; i--) {
outw(MDIO_ENB_IN, mdio_addr);
mdio_delay();
retval = (retval << 1) | ((inw(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
return retval>>1 & 0xffff;
}
static void mdio_write(int ioaddr, int phy_id, int location, int value)
{
int write_cmd = 0x50020000 | (phy_id << 23) | (location << 18) | value;
int mdio_addr = ioaddr + Wn4_PhysicalMgmt;
int i;
if (mii_preamble_required)
mdio_sync(ioaddr, 32);
/* Shift the command bits out. */
for (i = 31; i >= 0; i--) {
int dataval = (write_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
outw(dataval, mdio_addr);
mdio_delay();
outw(dataval | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
/* Leave the interface idle. */
for (i = 1; i >= 0; i--) {
outw(MDIO_ENB_IN, mdio_addr);
mdio_delay();
outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
return;
}
#ifdef MODULE
void
cleanup_module(void)
{
struct device *next_dev;
#ifdef CARDBUS
unregister_driver(&vortex_ops);
#endif
/* No need to check MOD_IN_USE, as sys_delete_module() checks. */
while (root_vortex_dev) {
next_dev = ((struct vortex_private *)root_vortex_dev->priv)->next_module;
unregister_netdev(root_vortex_dev);
outw(TotalReset, root_vortex_dev->base_addr + EL3_CMD);
release_region(root_vortex_dev->base_addr, VORTEX_TOTAL_SIZE);
kfree(root_vortex_dev);
root_vortex_dev = next_dev;
}
}
#endif /* MODULE */
/*
* Local variables:
* compile-command: "gcc -DMODULE -D__KERNEL__ -Wall -Wstrict-prototypes -O6 -c 3c59x.c `[ -f /usr/include/linux/modversions.h ] && echo -DMODVERSIONS`"
* SMP-compile-command: "gcc -D__SMP__ -DMODULE -D__KERNEL__ -Wall -Wstrict-prototypes -O6 -c 3c59x.c"
* compile-command-alt1: "gcc -DCARDBUS -DMODULE -D__KERNEL__ -Wall -Wstrict-prototypes -O6 -c 3c59x.c -o 3c59x_cb.o"
* c-indent-level: 4
* c-basic-offset: 4
* tab-width: 4
* End:
*/
References: